Hello all! I hope everyone is doing well all things considered....
I am putting together an AR10 .308 for general purpose use as well as wild hog hunting. What bullets have yall found to be sub...
Type: Posts; User: UH60_TrunkMonkey
Hello all! I hope everyone is doing well all things considered....
I am putting together an AR10 .308 for general purpose use as well as wild hog hunting. What bullets have yall found to be sub...
Congratulations on retirement! I've got a few years left. Welcome to the forum.
I work in Macon. Do you work on base?
Welcome, Where in GA? I am about 30 minutes south of Atlanta off I-75.
You mentioned Gen 2, have you replaced the recoil spring and other wear items recently?
Limp wrist and an incorrect reassembly could have done it also.
Hello all,
I no longer have the time to do much long range shooting so I am selling my 224 Valkyrie upper. It was assembled by Dedicated Technologies in MN.
22 inch Shilen Select Match 6.5...
Check out the Safariland ALS holsters. I use several including one on-duty as a LEO. If you want some customization check out RedHill Tactical. I am one of their sponsored competitive shooters and...
I guess I misunderstood their website then. It said "Most feature our exclusive InterLock® design — a raised ring inside the jacket that is embedded in the bullet's core that keeps the core and...
Any bonded soft point (which the interlock is) or the all copper TSX/TTSX bullets should be fine. Find a recipe that shoots straight with what you have. I haven't taken a bison nor had to shoot...
I use Applied Ballistics. It was developed by renowned long range shooter Brian Litz. I have used it to connect at 1,240 meters with a 308, and 2,200 meters with a 338 Lapua. There is a one time $20...
I like the Barnes line... TSX, TTSX
Have you tried threading the die slightly deeper into the press? The issue could be the shoulder needs to be bumped a few thousandths more. try about 1/8 to 1/4 turns at a time.
Some folks are...
Using 167 grain Lapua Scenar and 43.0 of 4064 I was at 2666 fps in my 20 inch. Your velocity should be just fine. As SAWMAN suggested, check your twist. If slower than a 1:10 you may want to consider...
I will back-up what Cody said. I load 125 Nossler ballistic tip using the fmj data for H110 from the Lyman 50th book. I have had great results with it on wild hogs.
The 1:7 will stabilize just about anything 224, it may even work for the 95smk. I know the 1:6.5s do. I load the 90smk in my 224V.
What are you looking to do with it? Punch steel or paper at...
Did I miss the gas system length?
Most 300blk subsonic need a pistol length gas system. They can be made to cycle with carbine gas but I'm not sure how.
Sent from my SM-G920V using Tapatalk
I have one from Dedicated Technologies. It is a 22 inch Shilen select match barrel 1:6.5 twist. Upper was squared and trued. Using brass and 90 SMK (from Wes) it will do sub half moa when I do my...
Army 2002-2016
Sent from my SM-G920V using Tapatalk
Has anyone run H335 in a suppressed 223 AR? I have a pound of it and plan on comparing the dirtiness level of it to W748.
I would load for however you intend to use it the most. Meaning if it will mainly be suppressed, develop your load with the can attached.
I have found in my defensive ARs that the accuracy and...
Wes, are these what he uses? https://uploads.tapatalk-cdn.com/20190113/d6e2db20a9d6380e3a4b3b884d7827a6.jpg
Sent from my SM-G920V using Tapatalk
Can yall recommend a 300blk bullet for taking hogs? Supersonic and available from Wes. This is my first time hunting something besides deer, coyote, and insurgents.
The photos are the new FLIR...
Use a case gauge. If if extends out the bottom, trim it. If it doesn't leave it be. Too short is not an issue typically. Too long can be. You can also use the gauge to make sure the shoulders are set...
Look at the SilencerCo Omega. I love mine. It sounds great on 308, 224 valkyrie, 6XC, 223, and 300blk. It can be mounted with a QD break or flash hider or direct thread. You can get a 30cal end cap...
I shoot a good bit of long range and yes velocity matters. To me though I would rather find a high end of moderate as to prolong the match grade accurate life of the barrel. The PRS guys can easily...